+7 706 617 16 36
GeoSupplies Hub › Dimatec core bits

Dimatec Inc. · Made in Canada

Dimatec diamond core bits — delivered to Kazakhstan in 10 days

Impregnated core bits, reaming shells and casing shoes by Canadian manufacturer Dimatec for exploration and mine-site core drilling. We match the matrix to your rock and rig, and custom bits are made in the shortest possible time.

  • Manufacturer with 30+ years of experience, Winnipeg, Canada
  • XT, S, HR and D series — from soft ground to quartzite
  • AQ, BQ, NQ, HQ, PQ, HWL, triple-tube and thin-wall sizes
  • Contract, invoice and closing documents for companies and tenders
The Dimatec range: diamond core bits, RS-5 reaming shells, casing shoes
Dimatec impregnated diamond core bit, view of the matrix crown face
Made in Canada 10-day delivery
10 daysdelivery to Kazakhstan
30+ yearsmanufacturing in Canada
4 seriesXT · S · HR · D matrices
9 typesof waterway design

Why buy Dimatec through GeoSupplies Hub

10-day delivery

From Canada to Kazakhstan. Items not in stock are made by Dimatec in the shortest possible time.

Matched to your rock

Our drilling manager selects the matrix for your geology, rig and hole depth.

Every size

AQ to PQ, HWL, triple-tube and thin-wall bits, DCDMA and metric.

Built for the job

Impregnation depth, waterways and crown profile set for your drilling conditions.

Synthetic diamond

Engineered material with controlled properties, no natural diamond — suited to kimberlite exploration.

Documents and tenders

GeoSupplies Hub LLP: contract, invoice, closing documents, and bids in subsoil users' tenders.

212 m

Per Dimatec: on a project in Northern Ontario a bit drilled 212 m where the previous bits lasted 60–80 m.Customer testimonial on the manufacturer's site

Dimatec matrix series: which one fits your drilling

XTHard and ultra-hard rock
Dimatec XT — Hard and ultra-hard rock

Dimatec's most advanced matrix technology for hard, tough formations when you need maximum performance.

Matrices: XT7 – XT15
SHigh-powered hydrostatic rigs
Dimatec S — High-powered hydrostatic rigs

Proven matrices: long bit life without losing penetration, from soft abrasive to hard consolidated rock.

Matrices: S3 – S12
HRHard rock, low bit weight
Dimatec HR — Hard rock, low bit weight

High production in hard, consolidated, fine-grained rock with relatively low bit weight. HR13–HR14 for high-powered rigs.

Matrices: HR7 – HR14
DLower-powered mechanical rigs
Dimatec D — Lower-powered mechanical rigs

All-round performers proven in Mohs 4–7+ formations, especially softer abrasive ground.

Matrices: D2 – D10

Matrix selector by rock type

Pick the rock and your rig type — we show the matching matrices from Dimatec's selection chart. Our drilling manager will confirm the choice against your section.

Rock

Rig

Selection chart: series by rock hardness

← Soft, fractured, abrasiveHard, fine-grained, non-abrasive →
XT7–8
XT9–10
XT11–12
XT13–14
XT15
S3
S6
S7
S8
S9
S10
S11
S12
HR7
HR8
HR9
HR10
HR11
HR12
HR13
HR14
D2
D3
D4
D5
D6
D7
D8
D9
D10
Mohs4567~8
UCS30406080100120160200

XT positions are approximate, based on the S ↔ XT equivalence table. The chart is a general guide: site conditions and rig capability may call for adjustment.

Dimatec products — in stock and made to order

Dimatec — Impregnated diamond core bits

Impregnated diamond core bits

Core bits for wireline and conventional barrels. Synthetic diamond in a metal matrix, 6, 9, 12 or 16 mm impregnation, TSP and tungsten-carbide gauge protection.

XT · S · HR · DAQ – PQ, HWL

Geotechnical bits: PDC, TSP, tungsten carbide

Single-layer bits for soft, unconsolidated ground: PDC (Pax) for Mohs 2–4, TSP for Mohs 3–5 and fractured rock, tungsten carbide for very soft granular ground and milling steel in the hole.

PDC PaxTSPWC
Dimatec — RS-5 diamond reaming shells

RS-5 diamond reaming shells

Economical diamond-set reaming shell for core barrels up to 152 mm. Full matrix gauge ring with spiral waterways and 360° hole contact.

up to 152 mm
Dimatec — Long Ring and backend reamers

Long Ring and backend reamers

254 mm extended ring to limit deviation in deep holes; backend reamers replace the adapter coupling to stabilise the barrel.

AWL 48.0 – PWL 122.6 mm
Dimatec — Carbide reaming shells, field gauges, substitutes

Carbide reaming shells, field gauges, substitutes

Diamond-free shells for overburden drilling; hardened-steel field gauges to check wear; substitutes where no reaming is needed.

overburdenwear check
Dimatec — Casing shoes and rod shoes

Casing shoes and rod shoes

Diamond D-Series (3 mm) and Super Duty (6 mm, for bouldery overburden); Saw-Tooth and Carbide-Chip for clay, sand, gypsum and soft shale.

DCDMAmetric

Non-coring bits

Impregnated, PDC and hole-opener bits for drilling without core recovery.

impregnatedPDChole opener
Dimatec — Bits built for your project

Bits built for your project

Drillers Project programme: Dimatec develops a matrix for a specific site, exchanging field data on penetration and wear with the drillers.

Drillers Projectcustom matrix

Need something not listed?

Send a spec, a photo of your old bit or another maker's part number — we will find the Dimatec match and send a quote.

Get a quote

Dimatec product photos

Tap a photo to open it full size.

The Dimatec range: bits, reaming shells, shoes
S and HR series impregnated bits
S series bits, S3 to S12
Impregnated bit crown face
S11 HWL bit in factory packaging
Matrix close-up: impregnation, TSP and carbide
RS-5 diamond reaming shells
RS-5 reaming shell
Long Ring reaming shell, 254 mm
Casing shoes and rod shoes
Saw-Tooth carbide shoe
Carbide-Chip shoe
Reaming shell field gauge

How core drilling and the bit work

Where Dimatec tools work

The shoe advances casing through overburden, the bit cuts rock and forms the core, the reaming shell holds hole diameter.

123456789
  1. 1Casing
  2. 2Dimatec casing shoe
  3. 3Overburden
  4. 4Bedrock
  5. 5Drill rods
  6. 6Core barrel
  7. 7RS-5 reaming shell
  8. 8Dimatec diamond core bit
  9. 9Core

Inside an impregnated core bit

Diamonds run through the full matrix height: as it wears, fresh ones are exposed, so the bit keeps sharpening itself.

y123456
  1. 1Matrix with synthetic diamond
  2. 2y — impregnation depth (6–16 mm)
  3. 3Waterway
  4. 4TSP and tungsten-carbide gauge pads
  5. 5Steel bit body
  6. 6Thread to core barrel

Bit technology: waterways, crown profile, impregnation

Waterways

  • WRegular: ~3 mm canal waterways, the default.
  • TTurbo: extra partial waterways — less bit weight, faster penetration; kerf up to 9 mm.
  • TTT-Turbo: trapezoid canals, 8% less face contact; thick-kerf wireline, holes to 300 m.
  • TXWTrapezoidal extra-wide: 10% less face contact, needs higher pump rates.
  • XXWExtra-extra-wide 6.3 mm: about 40% more flushing capacity; holes of 300 m and deeper.
  • XXWFFFree-Flow: deep inlet passages protect soft core and resist silt blockage.
  • FDFace discharge: soft unconsolidated ground and triple-tube barrels.
  • SFDSlot face discharge: where silt or viscous fluid such as foam is in use.
  • VXVORTEX: helix canals, typically 25–40% faster in soft to medium rock, better core.

Crown profile

  • Flat face: kerf ≤ 7 mm, fractured ground.
  • V-Ring: wireline standard, hard consolidated rock, quick start at low bit weight.
  • Semi-round: kerf ≥ 25 mm, heavily fractured ground, oil and gas.
  • Tapered: controls hole deviation and drills past wedges.

Impregnation depth

Diamond layer (y) and gauge pads on a Dimatec bit crown
Diamond layer (y) and gauge pads on a Dimatec bit crown

6 mm for thin-wall metric B, D, T, TT, T2, T6; 12 mm standard for Q and WL sizes; 9 and 16 mm and custom depths on request.

Core bit sizes: AQ, BQ, NQ, HQ, PQ, HWL

SizeOutside Ø, mmInside Ø (core), mm
AQ / AWL47.627.0
BQ / BWL59.636.4
NQ / NWL75.347.6
NQ375.345.0
HQ / HWL95.663.5
HQ395.661.1
PQ / PWL122.085.0
PQ3122.083.0

Nominal DCDMA dimensions. Check against your barrel before ordering — our manager will help.

HWL bit operating parameters (Dimatec data)

SeriesBit load, kgSpeed, rpmPump rate, l/min
S9 / S103,596 – 6,194552 – 94662 – 94
S11 / S123,596 – 5,595552 – 94662 – 94
Dimatec S11 HWL core bit with box: 95.6 × 63.5 mm, 10TXW waterways, 12 mm impregnation
S11 · HWL · 95.6 × 63.5 mm · 10TXW · 12 mm impregnation · V profile

Equivalents: Dimatec vs Boart Longyear, Fordia, Epiroc, Hayden

GroundMohsDimatecFordia HEROEpiroc (Fordia)HaydenBoart LongyearBoyles BrosHardCore
Very soft<3–4S3HERO 3Shred2Purple—H2
Soft3–5S6 / XT7–8HERO 5 / HERO 7Ferro / KS5 / 6–94Blue / GreenNG7 / NG7AAH4
Medium hard5–7S8–S9 / XT9–10HERO 9Azure, Kuby / 9–11 / Shark 8A7 / 7AAYellowNG9 / NG9AAH6
Hard6–9S10 / S11 / XT11–12HERO 11Lava / Hobic 11AC / 9–119AA / 9AAAOrangeNG11 / NG11AAH8
Very hard8–10S12 / XT13–14—Kraken / 11–14XS5 / 12–14RedNG12H10
Extremely hard—XT15——————

Equivalence is approximate. Final matrix choice depends on rock and rig — confirm with our drilling manager.

How we work

  1. Request

    Web form or WhatsApp: size, rock, rig, quantity.

  2. Selection

    We pick the matrix, waterways, profile and impregnation depth.

  3. Quote

    You get a commercial offer with price and lead time.

  4. Delivery

    Delivered to Kazakhstan in 10 days with full documents.

FAQ

How long does delivery of Dimatec bits take?

Delivery from Canada to Kazakhstan takes 10 days. If an item is not in stock, Dimatec makes it in the shortest possible time; the exact lead time is stated in our quote.

How do I choose the bit matrix for my rock?

Consider rock hardness and abrasiveness and rig power: S for high-powered hydrostatic rigs, HR for hard rock at low bit weight, D for lower-powered mechanical rigs, XT for the hardest, toughest rock. Use the selector above or send your section to our manager.

Which bit sizes do you supply?

AQ, BQ, NQ, HQ, PQ and wireline AWL–PWL (including HWL), triple-tube NQ3, HQ3, PQ3, thin-wall metric, plus casing shoes for DCDMA casing.

How does XT differ from S?

S is a proven range balancing bit life and speed across many formations. XT is Dimatec's most advanced technology for hard, tough rock when maximum performance is needed.

Do you have equivalents to Boart Longyear, Fordia, Epiroc bits?

Yes, see the equivalence table: for example S10/S11 and XT11–12 work in the same conditions as Boart Longyear Orange and Fordia HERO 11. Equivalence is approximate.

Do you work with companies and tenders?

Yes. GeoSupplies Hub LLP signs contracts, issues invoices and provides closing documents, and bids in subsoil users' procurement.

How do I get a price?

Price depends on size, matrix, waterways and quantity. Send a request and we reply with a quote showing price and lead time.

Get a price quote

Fill in the form — WhatsApp opens with a ready request for our drilling manager. Or call us.

Your request is ready. Tap Send in WhatsApp and the manager gets it right away.

Contacts

Drilling manager

+7 706 617 16 36

requests and bit selection

WhatsApp and calls

+7 706 617 16 66

quick reply in the messenger

Email

info@geoshub.kz

gsh.kz · Corporate site

GeoSupplies Hub

29 Zhenis Ave, office 112, Astana, Kazakhstan

2GIS